Thursday, 30 October 2014

2014 batch 2: Currant mead (3) - Fermentation progress

I have spend several days monitoring how the fermentation has progressed:

Monday the 27th of October
The following day I opened the fermenter and sampled for gravity and pH.

pH: 3.84
SG: 1.110
Temp: NA

Bugger, I forgot to measure temperature (?). Never the less it is interesting to see that pH had fallen from 4.7 to 3.8 due to the CO2 produced by the yeast. This is still in the start-up of the fermentation so yeast count is probably increasing. The resulting SG shows a decrease in gravity of 0.010.

Then I added the second nutrient pack:
Fermaid K: 2.0 g
MAP: 4.0 g
MAC: 3.0 g
K2CO3: 2.0g
Total: 64 ppm N and 57 ppm K+

I poured about 30 ml of must into the tube containing the nutrients, swirled it a bit to make a slurry and poured the content into the fermenter. To my surprise the must started to foam very aggressively, and I started to worry that I would be cleaning the floor for sticky honey. Fortunately, the foam stopped a bit before the edge. Then I stirred the must quickly to dissolve the nutrients, closed the fermenter and re-attached the airlock.

Evening Tuesday the 28th of October

pH: 3.64
SG: 1.088
Temp: 25.7 C (?)

So pH had droåped even further. Even though I add carbonate with both MAC and K2CO3 it might push pH a bit but it will fall again at least within one day. SG was surprisingly low. Gravity had fallen 0.022 in just one day - that is about 1/5 of the sugar available for fermentation, i.e. at this rate the fermentation could be over in just 5 days, WOW. Temperature was high, but I am not sure I trust the reading. The room was 23 C so the fermentation should have raised the temperature by almost 3 C - seems like a lot.


I then added the 3rd nutrient pack which was identical to the second one above. This time I did an effort to slowly dissolve some of the additives, pour it in, add more must to tube, dissolved a bit and pour it in, etc.
Never the less I still got a lot of foam.



Evening Wednesday the 29th of October

pH 3.63
SG 1.066
Temp: 24.1 C

It seams like pH has leveled out despite addition of carbonate so the must is probably now well buffered by bicarbonate. Once again SG had dropped 0.022 which I am still surprised about. Temperature is now within the expected range just a bit above room temperature - great

The 4th nutrient pack was added with was also identical to the second. Even though I planned for 5 nutrient packs I will not be adding the 5th. Since OG was 1.120 and I expect a FG to be 1.013 for an ABV of 15 % or a drop of 0.107 then an SG of 1.066 corresponds to 50% of the fermentation progress. Most articles says that you should not add nutrients past this point, so I will stop here and see what happens.
_________________

The 5th nutrient was a bit smaller than the previous packs

Ferment K: 1.0g
MAP: 4.0 g
MAC: 3.0 g
K2CO3: 2.0 g
Total: 57 ppm N and 57 ppm K+

My plan was to add 300 ppm N and 255 ppm K+. As it turned out I will have added only about 240 ppm N and 200 ppm K+.

In the coming days i will continue to monitor SG and pH. If the rate continues the fermentation should finished by Saturday - that would be a new record for me :o). And I will use this SNA scheme with 4 additions in the future.



2014 batch 2: Currant mead (2) - Fermentation start

Recipe:

7200 g of Summer honey, 2014
140 g of Spring honey, 2014
5 Nutrient packs according to SNA scheme
Water to 20 L
3.5 L of currant juice

Starter:
As always I am aiming at a starting gravity of 1.120 which is so high that it could become difficult for the yeast to really get started - So just in case I initiated the fermentation with a starter at a little less than half the gravity.

I dissolved 140 g of "spring honey" in 800 ml warm water, covered the glass and let it cool to room temperature. 

pH: 5.98
SG: 1.058

Just before adding the yeast I whipped the solution with with a kitchen mixer to get as much air into the solution as possible. Then I added the yeast which again was White labs, Sweet Mead, WLP715, covered the opening of the glass and placed it on my home made magnetic stirrer. The solution was stirred once in a while to ensure good mixing. 

The starter was up and running Saturtday the 25th of October at noon

Mead fermentation:
In the evening of the 25th of I prepared the must.

All the honey (7.2 kg) was poured into a fermentor. I just left the honey container up-side down for a while to get as much honey out as possible. Then I heated 10 L of water to 70oC and poured in into the fermenter too. Some of the water was used to rinse the honey container to ensure that I got it all out. I started to stirr to dissolve the honey. When no more honey was sticking to the bottom of the fermentor I added about 5 L of cold tap water so that the total volume was just below 20 L and stirred the solution well again. Then I left it overnight to cool down. Following this procedure the solution was 40 C when I finished.

Sunday the 26th of October:
During the day I was checking the starter. It was quite clear that the fermentation was running. When not stirring I could see plenty of small bubbles making the surface almost vibrate.

In the evening I added Nutrition pack 1 to the mead:
Fermaid K: 3.0 g
MAP: 3.0 g
MAC: 1.0 g
K2CO3: 1.0g
Total: 47 ppm N and 28 ppm K+


I left the solution for a couple of hours and measured

pH: 4.66
OG 1.120
Temp: 23.0 C

Notice that just honey and water gives pH around 6 whereas pH is 4.7 when nutrients are added. This means that the buffer capacity of the honey is almost non-existent. OG was on the target :o)


The starter was added and the beaker was rinsed with about 2 dl of water. So the total volume was just above 20 L. Finally the lid was closed and the airlock was filled with water and placed securely in the lid. Time to wait for the first bubbles from the airlock


Monday, 27 October 2014

2014 batch 2: Currant mead - SNA scheme (JPEG)

I could not figure out how to attach a file to the blog, so I just scanned the SNA scheme that I prepared.

It look like this:

For some reason, the last line of the page is not scanned - that is what you get when you buy a cheap printer/scanner. 

Everything is calculated once you entered the weighed amounts. The scheme is set up for additions over 5 days but will be adjusted according to how this mead behaves. 

Sunday, 26 October 2014

2014 batch 2: Currant mead - SNA preparations

This time I will try to make a currant mead using the current juice I prepared this summer and have been storing in the freezer since (ref. HERE).

Secondly, I will try to keep the fermentation strong until the max ABV is reached by Staggered Nutrition Addition.

Basically there is not much else but glucose and fructose in the must. This means that if nutrients need to be added to avoid a sluggish fermentation. As far as I can find on the internet I need:
300 ppm of FAN/YAN
300 ppm of potassium.
and yeast nutrients in general.

For this I used Fermaid K and since I still have not been able to get DAP, I am using a mixture of monoammonium dihydrogen phosphate (or MAP) and monoammonium bicarbonate (MAC). MAC can also be purchased as the baking spice "Hartshorn" but be sure whether you purchase ammonium carbonate or ammonium bicarbonate. It appears that both are sold under the same name. Furthermore, DAP or MAC/MAP should not be added in high concentrations as it then becomes toxic to the yeast. The idea is to spread out the additions over several days and keep the concentrations at a consistent level for the major part of the fermentation.

As potassium source I used pot ash or potassium carbonate. This is also a quite basic compound so I decided to add it in a staggered fashion too so pH is not to high in the beginning and use it to raise pH a bit during the fermentation so that CO2 does not push pH too low. I cannot measure the content but based on the figures I can find on the web a general honey should contain about 200 ppm K+. In 20 L must that I intend to prepare the concentration becomes 53 ppm. Hence, I just need about 250 ppm to reach the 300 ppm needed.

I prepared a quite extensive spread sheet but in short the additions are as follows

day 1: 47 ppm N and 28 ppm K+
day 2: 64 ppm N and 57 ppm K+
day 3: 64 ppm N and 57 ppm K+
day 4: 64 ppm N and 57 ppm K+
day 5: 57 ppm N and 57 ppm K+
Total: ~300 ppm N and ~250 ppm K+

Or put in another way:

Total Fermaid K: 10g
Total MAP: 19 g
Total MAC: 13 g
Total pot ash: 9 g
i.e. total additions: 51 g

Everything added each day was weighed into 5 tubes (various amounts of Fermaid K, MAP, and MAC) and the tubes were labeled 1-5 so that it would be easy just to add one tube every day for 5 days



Finally I also prepared for an 800 ml starter with 33 ppm of N from Fermaid K only. Now I am ready to go.

I wonder if it is possible to add an Excel sheet to this blog for easy access...... Anyone?


...... and what to do with the abdicating queen.

When taking the old queen out I was wondering what I should do with her. I could not really get myself to just kill her and through her out, so I decided I would try to dry and exhibit her.

First I needed to kill her in a gentle way. I did not have any organic solvents at home so I just figured I would get her drunk in Bacardi :o). I put her in a glass with some beads to lift her from the Bacardi rum in bottom. It took longer than I expected and she was not dead until the next morning.


When I took out the queen she was damp and a bit curled up. The wing was sticking together so I needed to dry her in the position I wanted to exhibit her. A cork, a few pins and some precision work did the job - a pin in the neck, on each side of the body and positioning the legs and wings in a "natural" position.


Hereafter I just left her on a shelf to dry. Also, I did not have a plate to pin her to. I found a good frame in IKEA where the glass was lifted several centimeters from the picture. I found a piece of styrofoam about 1 cm thick and cut out a square which I then covered with a yellow dish washing cloth. This I could use as the surface to pin the queen too. I picked a yellow cloth because the contrast to the dark queen highlighted her details.

And voila!


Wednesday, 22 October 2014

New queen in the castle

Back to my bee hive....

After the formic acid treatment in september I had decided to change the queen in the hive. She is marked yellow which means that she from 2012. Last year the hive behaved great, but this year she had several times started to make swarm cells, i.e. cells for new queens.


If these are not removed, half the hive will swarm with either queen to a new location - typically a tree close by. This happened several time in "school hives" of the bee association that I am member of and it is quite an awesome thing to see - and to take down again.


The new queen bee that I bought is from this year 2014 and is labeled with a green mark.


 Changing queen is remarkably simple.

1. Remove the old queen and leave the hive without queen for a day. I caught one extra working bee with her which I could not get rid of.


2. Add the new queen in a place where the other bees cannot get to her and sting her to death. Leave the hive for half a day for the bees to get use to her pheromones.


3. Insert the new queen in the hive and let the bees work for her by digging her out and feeding her.


And the hive now has a new "monarch". Can you find her........ :o)


Tuesday, 21 October 2014

2014 batch 1: Cyser (4) Malolactic fermentation

Fermentation is over and the mead has been racked twice during the last 3 weeks.

The taste of the mead is pleasant but it still has a sting to it from the malic acid. For that purpose I had purchased Malolactic bacteria from White Labs (WLP 675). It is a suspension that must be kept refrigerated until use. I found instructions (HERE) where it stated that there should be about 5 Brix of residual sugar which corresponds to a gravity of 1.020. Secondly the bacteria can be propagated in apple juice (or tomato juice). Finally the bacteria has high tolerance for low pH (pH 3.0) and an optimal performance at approximately pH 4.0. The tolerance to alcohol is up to 15%. Working temperature is 21-23oC

So the conditions in my Cyser are close to PERFECT :o)

I took out the vial from the fridge 4 hours before use, shaking it periodically and then added the entire vial to the fermenter. The following day I got a few bubbles from the airlock, so the bacteria is already hard at work.


The flask to the right contains a small sample of the mead so that I can do taste tests as the malolactic fermentation progresses. I will also try to set up a TLC measurement to get a semi quantitative measurement of the progress - more on that later...