Sunday, 16 November 2014

2014 batch 2: Currant mead (6) - Back sweetening

It seems like the fermentation is still going but at a very slow rate. I measured the gravity to just 1.002 so this is likely part of the reason. I am surprised that my Sweet Mead Yeast has pretty much used the entire amount of sugar - Sweet Mead my a.. :o).

Tasting the mead, it has plenty of acidity and a slight taste of red currant. The smell and flavor of the black currant is gone, but the color of the mead is fantastic - a strong light red color. 

This is something to remember - use one third red currant for acidity and two thirds black currant to make up for color. 

Due to the acidity I figured some sweetness from honey would be welcome, so I decided to target a final gravity of 1.025. Using the calculations in last post in a spreadsheet looks like this:


With a target Oechsle of 25 and a starting Oechsle of 2 in a total volume of 23.5L, I need 1713 g. In fact I had about 1775 g left from my cyser (calculated using the tara value of the container)

I poured what I could into a clean bowl and dissolved it in 1.5 L of the mead. This takes a loooooong time when the liquid is not heated. With some patience it slowly dissolves. Then I poured the content of the bowl back into the fermenter and rinsed the bowl repeatedly with the mead. Then I poured some mead into the honey container to rinse it too. Judging from the tara value I had gotten about 1760 g out. This corresponds to a new Oechsle of 26. 

I left the fermenter overnight to fully dissolve the honey and measured the gravity the next day:


I read this as just slightly below 1.026, and well within expected uncertainties. The total volume is now 24.5 L so there will be mead enough for all.....

The equations work :o)


Tuesday, 11 November 2014

Back sweetening - The Honey-Oechsle equation

"Three is the magic number" as the saying goes, and that is right for honey too. I always use 7.2 kg of honey for 20L must because I know I will have a gravity of 1.120 or Oechsle value of 120 degrees. The ratio between Oechsle value and honey concentration, which I call the honey factor, is then equal to 0.3333, and hence the inverse of this factor is exactly 3. 


Using this factor, it then becomes very easy to calculate how much honey to use to reach any target Oechsle value.

Now, this factor can also be used when adding fruit juice, by expressing all the sugar content of the juice as honey. This calculation also takes into account the additional volume. In the end the honey factor is eliminated. As the examples show, you can either calculate the new Oechsle value when adding a fixed volume of juice/extract, or you can calculate how much juice/extract you need to reach a target Oechsle value.


Finally you can use the same set-up for calculating how much honey to use for back sweetening. This time you will need the inverse honey factor and the density of the honey. I usually use the value 1.35 g/ml for the density which is used to calculate the volume increase. As before, examples illustrate how you can either calculate the new Oechsle value when adding a fixed mass of honey, or you can calculate how much honey you need to reach a target Oechsle value.
  

These calculations work great in Excel and they are a great help if you, for example, want to add honey to a target Oechsle value and be spot on first time :o)

Limitations
What are the limitations? The equations do not take into account that the gravity is lowered due to the content of alcohol. If all has been converted to ethanol, the density should not be lower than 0.970, i.e. a correction of 3% would be needed. But 3% is likely well within the error of all values going into the equations, and it would not improve your result significantly.

The inverse honey factor are of cause dependent on the water content of the honey. As a mead maker you will of cause be using high quality honey where the water content is only 15-17%, i.e. within a quite narrow range. Hence, this variation in sugar content will also be small.

The biggest contributor to error is, as I see it, the density of honey. I do not have data showing the variations in density in various honeys. Never the less, the density is used to calculate the added volume, and this volume will always be small compared to the volume of the must, i.e. a large error will not influence the new Oechsle value very much.

Mixing volumes might not be exactly equal to the sum of the individual volumes, but again the correction would be smaller than the error of other values. 







Monday, 3 November 2014

2014 batch 1: Cyser (6) Adding yeast stopper

Sometimes in between kids dinner and diapers and bed time my head is just not screwed on right. When I did the racking of the cyser yesterday and even realized that the mead is almost to lactic, I forgot to add the sodium metabisulfite/potassium sorbate that should inhibit the malolactic bacteria. Even though the airlock is not bubbling regularly the process could still be ongoing at a slower rate, and I do not want any more lactic acid in the cyser if I can avoid it.

So today I added the sodium metabisulfite/potassium sorbate today and gave the fermenter a good stir, but no splashing. Thank god I remembered

Just as last year it comes in a prepacked mix that should be adequate for 20 L batches. The total mass of content should be 7 g. So another thing on the to do list is to figure out how much of each component there are in a package.

Sunday, 2 November 2014

2014 batch 1: Cyser (5) Racking and sampling

Also racked the Cyser today. It has stopped bubbling and the water in the airlock has leveled out. The data was

SG: 1.016
pH: 3.68
Temp: 24.7 C

I took another sample for the TLC analysis that I have not yet had time to set up .... it will soon be on the top of the "to do list"

The transformation of the taste is quite significant. The stinging acidic taste of the malic acid is completely gone and the mead now has a slight yogurt like taste to it which will hopefully not become any more pronounced. It is quite pleasant to drink but I think back sweetening with honey to SG 1.020 - 1.025 will do wonders.

2014 batch 2: Currant mead (5) - Addition of currant juice

In the afternoon Saturday the 1st of November I took out the currant juice from the freezer. The juice was prepared this summer as described HERE. It is the steamed juice of red currant and black currant from the  ribes bushes in our garden. The volume is about 3.5 L and consist of approximately 1.25 L of red currant juice, and 2.25 L of black currant juice

Sunday the 2nd of November
In the morning I checked that the juice had thawed and the temperature was just below room temperature. I emptied the juice into a clean fermenter and then I just racked the batch onto it, stirred a bit, and closed it up. After the addition SG was 1.011 so there was plenty of sugar in. Secondly the total volume is now 23 L, so assuming that I was at about 15% ABV at the time of racking, I am now at 13%. Further more, if 1% ABV is generated from a gravity change of 0.00753, then the mead can potentially convert a gravity of 1.015 to 1.000, i.e. I am a bit short in sugar - 0.004 gravity units

So if 7.2 kg gives a gravity of 1.120 then I am 240 g of honey short. So I added 300g (actually 295g) which should add about 0.005 to the gravity.

About 5 hours later I measured gravity and pH again
SG: 1.011
pH: 3.41
Temp: 24.7 C

I noticed that pH dropped significantly when adding the juice - from 3.7 to 3.4. Also the mead is now foaming quite a bit so there was plenty of proteins in the juice also. I am not sure this was a good thing. If the fermentation stops completely, some not so pleasant compounds might be present due to partially degraded protein. Well, now I will just have to see if the fermentation will run for at least 24-48 hours more and then stop before the batch runs out of sugar :o).
______________

In all calculations I do not take into account that ethanol lowers the density of the solution. All measurements are with quite large uncertainty anyways, so adjusting for ethanol content by extensive calculations just seems like overkill. 

2014 batch 2: Currant mead (4) - fermentation is ending after just week :o)

I continued to monitor the gravity, pH and temperature after the last addition. All measurement were done in the evening so that the intervals between measurements were as close to 24 hour as possible

Thursday the 30th of October
Sg: 1.040
pH: 3.69
Temp: 23.6 C

Friday the 31th of October
Sg: 1.022
pH: 3.68
Temp: N.A.

Saturday the 1st of November
Sg: 1.010
pH: 3.70
Temp: 22.7 C

So how does this SNA batch compare with the cyser. When plotting the gravity readings you get


I called it Sack as the currant juice has not been added yet, so as of now it is produced as a Sack mead. It is very clear what with Staggered Nutrition Addition you get a very fast and consistent fermentation (almost linear progress), which is at the end after 6-7 days :o)

Basically I had estimated that that a drop of 0.100 would correspond to 14 %. Hence if the yeast max out at 15%, it should not change gravity by more than 0.107 and should in this case have stopped at 1.013. Now it is 1.010 and it is still going strong even though the rate has been reduced a bit

The simple formula for calculating Alcohol by volume is:
ABV= (OG-FG)/0.00753 (ref wikipedia)
This basically says that the gravity changes by 0.00753, then 1% of alcohol is produced.

For high gravity there is a somewhat more complicated formula.
ABV =76.08*(OG-FG)/(1.775-OG)*FG/0.794
The idea is that more ethanol is produced at the end of the fermentation since the replication rate reduces. This means that more alcohol should be produces per gravity unit.

The high gravity formula (alternative formula) as it is returns ridiculously high ABV values - far higher than the yeast max, so I just adjusted the simple formula by using a factor of 0.0071. So 15%max x 0.0071 = 0.107.

Right now I am back to the original simple formula. Then, for an ABV of 15% the new low is 1.007 instead of 1.013.

Friday, 31 October 2014

pH meters - which one to buy

I have been looking at several blogs to see which pH meters were used by home brewers. It is a fantastic tool, but can also be quite expensive. Never the less I recommend that everyone with an interest in the details of how your wine, mead or beer develops to purchase a proper pH meter. But as always it is important to look around before you buy.

I came across 5 different brands with pH meters with products that could be used for home brewing. These were

Hanna Instruments
Milwaukee Instruments
Adwa Instruments
HM Digital and
Atago

Other brands are available on the web but as far as I know these are not available from danish suppliers. These are:
Omega (PHH-7011)
Hach (H series H160 or H170)
LaMotte (Tracer Pocket Tester)
.... (Let me know which ones I missed) ....


Hanna-, Milwaukee-, and Adwa- Instruments
Researching the web I made an interesting observation. Hanna, Milwaukee, and Adwa are very likely the same company. They all have office at EXACTLY the same address in Hungary. 
...Alsókiköto sor 11., H-6726 Szeged....
So if prices for these 3 brands are similar, it is not a surprise.  

It bothers me quite a bit that one company are giving the customer a sense of choice by producing different brand names but are in fact selling the same "crap in different wrapping".

So the choice was now down to HM Digital and Atago. 

HM digital
HM is a US company and their pH meters are produced in South Korea. They sell 2 different pH meters that are useful for home brewers:
pH 80 and
pH 200
The main difference is the resolution. pH 80 show results with one decimal and pH 200 with 2 decimals. 

Atago
Atago is a japaneese brand and sells only one pH meter - the DPH-2. This pH meter only has a resolution of 1 decimal. 

The Choice...
Hereafter it was quite easy for me to choose, and I purchased the pH 200 from HM Digital. As a bonus it was also cheaper than the "Hungarian Huddle" 


I will try it out for a while before reviewing it. As for now, it is fulfilling all expectations.